B

brewtroller

Settings | Report Duplicate

0

I Use This!

Inactive

Commits : Listings

Analyzed about 3 hours ago. based on code collected about 3 hours ago.

Commit Message	Contributor	Files Modified	Lines Added	Lines Removed	Code Location	Date
Aug 17, 2024 — Aug 17, 2025 Showing page 6 of 13 Search / Filter on:
Fixing bugs related to DIGITAL_INPUTS not being defined for certain boards.	mattreba	More...				over 13 years ago
Added support for Triggers including EStop, Sparge Max Volume and HLT/Mash/Kettle Min Volume.	mattreba	More...				over 13 years ago
Fixed an issue that would cause the code to fail to compile when no PVOUT is defined.	jvonnieda	More...				over 13 years ago
Fixed issues with softswitches on PV out. Added new Valves.get() method. Changed valve bits to set when computedBits is different than the currently set bits. This is required to make sure that softswitches take effect even when the active profiles have not changed.	jvonnieda	More...				over 13 years ago
First commit of RGB board support. Not quite complete, but want to start getting it controlled. Only two more small things left to do.	jvonnieda	More...				over 13 years ago
Added family code check to 1-Wire temp Sensor Scan	mattreba	More...				over 13 years ago
Reverting to BT4 Pro HWProfile.h	mattreba	More...				over 13 years ago
Modified to use combined GPIO and I2C Encoder library.	mattreba	More...				over 13 years ago
Fixing Build Number.	mattreba	More...				over 13 years ago
Support for I2C Encoder and variable number of digital input pins.	mattreba	More...				over 13 years ago
Updated HWProfiles for OpenTroller DX1 Prototype	mattreba	More...				over 13 years ago
Disable the direct fire rims stuff by default.	jvonnieda	More...				over 13 years ago
Merged in the DirectFiredRims branch 774:879 .	treaves	More...				over 13 years ago
Reverting commit 831 from devon_dallmann.	treaves	More...				over 13 years ago
Fix a bug where if the user did not have AUTO_GRAIN_IN_EXIT turned on with a value of 0 the AUTO_ML_XFR code would not shut off the sparge in valve profile when target HLT volume is reached, same if you use the AUTO_IN from the sparge window (the one shown during grain in) and did not have AUTO_ML_XFR on.	devon_dallmann	More...				over 13 years ago
git-svn-id: http://brewtroller.googlecode.com/svn/trunk/BrewTroller@831 786cebc4-e6f9-11dd-9c15-fdd50ba39c1e	devon_dallmann	More...				over 13 years ago
Fixing Brightness control for BT Lite	mattreba	More...				almost 14 years ago
Fixing brightness control for BT Lite	mattreba	More...				almost 14 years ago
Fixed temperatures to default to BAD_TEMP value on boot up to resolve issue with 0C/0F temps being displayed in place of '---' and incorrect averaging when sensors are disconnected or not configured.	mattreba	More...				almost 14 years ago
Fixing Boil UI display bug and PV MUX issue for BT 3.3 boards.	mattreba	More...				almost 14 years ago
Fixing Build Number	mattreba	More...				almost 14 years ago
Fixing Build Number	mattreba	More...				almost 14 years ago
Fixing Boil UI display bug and PV MUX issue for BT 3.3 boards.	mattreba	More...				almost 14 years ago
Fixing Boil UI display bug and PV MUX issue for BT 3.3 boards.	mattreba	More...				almost 14 years ago
Fix a bug I noticed where if using the min hlt refill value the wrong amount of sparge water could be loaded during refill because the value grabbed was the min when you wanted the max.	devon_dallmann	More...				almost 14 years ago
BrewTroller 2.5	mattreba	More...				about 14 years ago
Moving BrewTroller 2.4 to Testing	mattreba	More...				about 14 years ago
Fixing Autoreset Bug caused by Latch pin remaining set.	mattreba	More...				about 14 years ago
Fixing Autoreset Bug caused by Latch pin remaining set.	mattreba	More...				about 14 years ago
Fixing Autoreset Bug caused by Latch pin remaining set.	mattreba	More...				about 14 years ago

←
1
2
3
4
5
6
7
8
9
10
11
12
13
→